INITIAL HW · ELECTRONICS SYSTEMS ENGINEERING

Ideas become
working
hardware.

PCB design, firmware, embedded Linux, and custom enclosures—from requirements to tested hardware prototypes.

Your project. One engineering partner.

PROJECTS

Featured projects.

SYSTEM DESIGN / FLIGHT COMPUTING

Zynq flight computer

A reusable Linux platform for rocketry avionics.

Used during a successful 5.5 kN liquid-engine test firing, managing sensing, control, telemetry, and data acquisition.

Project details

Linux runs the high-level software. FPGA fabric and expansion interfaces support mission-specific functionality.

Compute
Xilinx Zynq XC7Z030 · 1 GB DDR3 · eMMC
Interfaces
Gigabit Ethernet · Wi-Fi · FMC expansion · PCIe
Sensing
IMU · barometer · temperature · GNSS
Power
USB-C or battery, with integrated power-path multiplexing

Responsibility: complete system design, hardware, embedded software, bring-up, integration, and test validation.

FIRMWARE / FLIGHT COMPUTING

STM32H7 flight computer

Flight firmware and a telemetry UI for a dual-core STM32H7 platform.

Controlled a successful rocket flight to 3 km apogee, managed airbrakes and recovery deployment, and guided a parachute payload to a predetermined target.

Project details

Controlled recovery deployment and variable-apogee airbrakes, and guided a parachute payload to a predetermined target.

Compute
Dual-core STM32H7
Navigation
GNSS
Communications
CAN bus · LoRa integration
Outputs
Pyro channels

Contribution: firmware, telemetry UI, assembly, bench testing, and validation.

BOARD DESIGN / POWER SYSTEMS

Power-path test board

A test board for switching between USB-C and battery power.

30 W USB-C input and battery-powered DC-DC conversion delivering 5 V at up to 12 A / 60 W.

Project details
USB-C input
Up to 30 W
Battery regulation
9–36 V input to 5 V output, up to 12 A / 60 W
DC-DC stage
Automotive-grade switching with input-transient handling
Power paths
USB-C and battery switching, with access for bench testing

Contribution: test-board design.

BOARD DESIGN / SENSING & TELEMETRY

Aurora V1 telemetry module

A 50 × 50 mm telemetry board with integrated sensors, radio, and local storage.

Project details
Compute & radio
STM32F446 · 433 MHz RF module
Sensing
Motion, pressure, temperature, humidity, and magnetic field
Storage
microSD and NAND flash for local telemetry logging
Interfaces
USB-C · battery input · SWD debug

Contribution: board design.

The KiCad preview omits some unavailable component models.

CAPABILITIES

Hardware, software
and enclosure design.

Custom electronics, from circuit design to hardware prototypes. These technologies are examples from past work; your requirements set the scope.

Send a project brief
System & PCB design

System architecture, schematic design, and PCB layout, including component selection, manufacturing files, prototype bring-up, and validation.

ArchitectureSchematics & PCBRedundancyBring-up & validation
High-speed digital

DDR memory and high-speed interfaces, including board design and integration for FPGA-based hardware.

DDR memoryEthernetFPGA-based hardwareHigh-speed interfaces
Power & analog electronics

DC conversion and regulation, power-path switching, analog signal conditioning, and audio amplifiers.

DC powerPower multiplexingAnalog & mixed-signalAudio amplifiers
Connectivity & sensing

Analog and digital sensor interfaces, wired buses, and Wi-Fi / RF module integration, with the required drivers.

Analog sensorsWi-Fi & RFSPI / I²C / UARTCAN / FDCANEthernet
Firmware & embedded Linux

Embedded firmware development, peripheral drivers, Linux kernel and board support, and hardware bring-up.

Embedded firmwarePeripheral driversLinux kernelBoard bring-up
Custom enclosures & fabrication

Enclosures designed for the PCB, connectors, mounting, and access. Prototype and PCB fabrication coordinated alongside the design.

Enclosure designMechanical integrationPrototype fabricationPCB fabrication coordination

DESIGN PROCESS

From brief
to tested hardware.

  1. 01

    Define the scope

    Agree on requirements, interfaces, deliverables, and a build plan.

  2. 02

    Design & build

    Design the electronics and software, arrange fabrication, and bring up the prototype.

  3. 03

    Validate & hand over

    Test against the agreed requirements and hand over the project files and documentation.

Agreed project handover

Deliverables can include schematics, PCB files and Gerbers, firmware source and documentation, enclosure CAD files, user manuals and test reports—as agreed in the project scope.

START A PROJECT

Start your
project.

Send a short outline of what you need to build, or book a meeting.

[email protected]
Contact · George Krystallis
What should it do, and when do you need it?

Opens an email draft for you to review and send.